High-speed equalization and transmission in electrical interconnections

Ondertitel:Hogesnelheidsegalisatie en -transmissie in elektrische interconnecties

The relentless growth of data traffic and increasing digital signal processing capabilities of integrated circuits (IC) are demanding ever faster chip-to-chip / chip-to-module serial electrical interconnects. As data rates increase, the signal quality after transmission over printed circuit board (PCB) interconnections is severely impaired. Frequency-dependent loss and crosstalk noise lead to a reduced eye opening, a reduced signal-to-noise ratio and an increased inter-symbol interference (ISI). This, in turn, requires the use of improved signal processing or PCB materials, in order to overcome the bandwidth (BW) limitations and to improve signal integrity. By applying an optimal combination of equalizer and receiver electronics together with BW-efficient modulation schemes, the transmission rate over serial electrical interconnections can be pushed further. At the start of this research, most industrial backplane connectors, meeting the IEEE and OIF specifications such as manufactured by e.g. FCI or TE connectivity, had operational capabilities of up to 25 Gb/s. This research was mainly performed under the IWT ShortTrack project. The goal of this research was to increase the transmission speed over electrical backplanes up to 100 Gb/s per channel for next-generation telecom systems and data centers. This requirement greatly surpassed the state-ofthe-art reported in previous publications, considering e.g. 25 Gb/s duobinary and 42.8 Gb/s PAM-4 transmission over a low-loss Megtron 6 electrical backplane using off-line processing. The successful implementation of the integrated transmitter (TX) and receiver (RX) (1) , clearly shows the feasibility of single lane interconnections beyond 80 Gb/s and opens the potential of realizing industrial 100 Gb/s links using a recent IC technology process. Besides the advancement of the state-of-the-art in the field of high-speed transceivers and backplane transmission systems, which led to several academic publications, the output of this work also attracts a lot of attention from the industry, showing the potential to commercialize the developed chipset and technologies used in this research for various applications: not only in high-speed electrical transmission links, but also in high-speed opto-electronic communications such as access, active optical cables and optical backplanes. In this dissertation, the background of this research, an overview of this work and the thesis organization are illustrated in Chapter 1. In Chapter 2, a system level analysis is presented, showing that the channel losses are limiting the transmission speed over backplanes. In order to enhance the serial data rate over backplanes and to eliminate the signal degradation, several technologies are discussed, such as signal equalization and modulation techniques. First, a prototype backplane channel, from project partner FCI, implemented with improved backplane connectors is characterized. Second, an integrated transversal filter as a feed-forward equalizer (FFE) is selected to perform the signal equalization, based on a comprehensive consideration of the backplane channel performance, equalization capabilities, implementation complexity and overall power consumption. NRZ, duobinary and PAM-4 are the three most common modulation schemes for ultra-high speed electrical backplane communication. After a system-level simulation and comparison, the duobinary format is selected due to its high BW efficiency and reasonable circuit complexity. Last, different IC technology processes are compared and the ST microelectronics BiCMOS9MW process (featuring a fT value of over 200 GHz) is selected, based on a trade-off between speed and chip cost. Meanwhile it also has a benefit for providing an integrated microstrip model, which is utilized for the delay elements of the FFE. Chapter 3 illustrates the chip design of the high-speed backplane TX, consisting of a multiplexer (MUX) and a 5-tap FFE. The 4:1 MUX combines four lower rate streams into a high-speed differential NRZ signal up to 100 Gb/s as the FFE input. The 5-tap FFE is implemented with a novel topology for improved testability, such that the FFE performance can be individually characterized, in both frequency- and time-domain, which also helps to perform the coefficient optimization of the FFE. Different configurations for the gain cell in the FFE are compared. The gilbert configuration shows most advantages, in both a good high-frequency performance and an easy way to implement positive / negative amplification. The total chip, including the MUX and the FFE, consumes 750mW from a 2.5V supply and occupies an area of 4.4mm × 1.4 mm. In Chapter 4, the TX chip is demonstrated up to 84 Gb/s. First, the FFE performance is characterized in the frequency domain, showing that the FFE is able to work up to 84 Gb/s using duobinary formats. Second, the combination of the MUX and the FFE is tested. The equalized TX outputs are captured after different channels, for both NRZ and duobinary signaling at speeds from 64 Gb/s to 84 Gb/s. Then, by applying the duobinary RX 2, a serial electrical transmission link is demonstrated across a pair of 10 cm coax cables and across a 5 cm FX-2 differential stripline. The 5-tap FFE compensates a total loss between the TX and the RX chips of about 13.5 dB at the Nyquist frequency, while the RX receives the equalized signal and decodes the duobinary signal to 4 quarter rate NRZ streams. This shows a chip-to-chip data link with a bit error rate (BER) lower than 10U+221211. Last, the electrical data transmission between the TX and the RX over two commercial backplanes is demonstrated. An error-free, serial duobinary transmission across a commercial Megtron 6, 11.5 inch backplane is demonstrated at 48 Gb/s, which indicates that duobinary outperforms NRZ for attaining higher speed or longer reach backplane applications. Later on, using an ExaMAX® backplane demonstrator, duobinary transmission performance is verified and the maximum allowed channel loss at 40 Gb/s transmission is explored. The eye diagram and BER measurements over a backplane channel up to 26.25 inch are performed. The results show that at 40 Gb/s, a total channel loss up to 37 dB at the Nyquist frequency allows for error-free duobinary transmission, while a total channel loss of 42 dB was overcome with a BER below 10U+22128. An overview of the conclusions is summarized in Chapter 5, along with some suggestions for further research in this field. (1) The duobinary receiver was developed by my colleague Timothy De Keulenaer, as described in his PhD dissertation. (2) Described in the PhD dissertation of Timothy De Keulenaer.

ISBN:9789085788409

Jaar van publicatie:2015

Toegankelijkheid:Open